For VAG Vehicle Diagnostic Interface VVDI with 4th Immo update tool
1. Support NEC 24C32 change mileage through obd2, generate dealer's keys, read and write EEPROM and backup flash data.
2. Support GOLF5 MM7(9S12) change mileage through obd2, generate dealer's keys, read and write EEPROM and backup flash data.
3. Add TA special chip pre-program. Directly pre-program ID48 to TA2,TA3, TA4, TA5 chips.
Latest version:V 13.2
Language:English, Chinese etc.
Update: By Email
Suggest System: Windows XP
Tips: Work with VVDI China VAG Vehicle Diagnostic Interface with 5th Immo update tool, it can do VW fifth generation of anti-theft system
Attention: IMMO PLUS 2.0 software and VAG Commander software can use VVDI hardware together, but previous VVDI customer need update hardware then can support IMMO Plus software.
1. Extracting security access codes (PIN. by OBDII
2. Programming keys by OBDII. Preparation of dealer's keys.
3. Mileage recalibration by OBDII
4. Clearing crash data DTCs by OBDII
5. Read/Program flash memory of engine control units by OBDII. Options for resetting the number of flashing attempts.
6. Exchange speed limit of MMI-TV system
1.Standard diagnostic functions:
1. Connect to the device using KWP2000 over TP2.0, KWP2000 over TP1.6, UDS over ISO transport protocol (CAN., KWP1281 or KWP2000 over K-Line
2. For all electronic control units reading identification data
3. For all electronic control units read error (DTCs.
4. For all electronic control units clear error (DTCs.
5. Scan all units
6. Broadcast requests
7. Measured values
2.Function in addition:
1.According to obd2, the latest VVDI supports nec 24c32 mileage change, dealer key generation, EPPROM data reading & writing, FLASH backup.
2.According to obd2, the latest VVDI supports GOLF6 MM7(9S12) mileage change, dealer key generation, EPPROM data reading & writing, FLASH backup.
3.Add the function of professional TA chip pre-program, it directly pre-programs 48 chip into TA2, TA3, TA4, TA5.
Support Vehicle Model List:
1 AN002 - KM-CAN
1 AN003 - PIN-CAN
1 AN004 - IMMO panel
1 AN005 - IMMO panel EDC16
1 AN006 - KM/PIN K-Line
1 AN008 - Flash Counters
1 AN009 - Key learning
1 AN010 - Airbag EEPROM
1 AN011 - TV Activation
1 AN012A- EDC16 Odometer
1 AN012B- EDC16 EEP/PIN/IMMO-off
1 AN014 - EDC17 EEPROM
1 AN015 - Flash Memory ECU
1 AN016 - Dealer key learning
1 AN018 - Dealer key learning Q7
1 AN019 - Prepare Dealer Key Q7
1 AN021 - ME7 EEPROM by CAN
1 AN022 - CDC32xx Programmer
1 AN027 - Q7 2008
VAG Vehicle Diagnostic Interface VVDI for the vehicles VW Audi is a Windows-Based diagnostic software. With the help of VAG Vehicle Diagnostic Interface VVDI you can perform operations with vehicles from the VAG group, which are in most cases unsupported from the producer diagnostic testers. The VAG Vehicle Diagnostic Interface VVDI for VAG provides you also full diagnostic capabilities for VAG-vehicles.
1) Instrument CAN
(1) With this function you can establish diagnostic session with the Instrument cluster using KWP2000 over TP2.0
(2) You can read current odometer value
(3) You can change odometer value
(4) Added support for VDO Instrument Cluster 2006+
(5) Read/Program memory of instrument cluster immobilizer
(6) Reading security access code of the IMMOBILIZER
(7) Read/Write immobilizer related data
2) EZS - Kessy (Q7/A6/Allroad)
(1) With this function you can prepare dealer key/learn dealer key
(2) Read/Write eeprom from EZS - Kessy (Q7/A6/Allroad)
3) Instrument K-Line
(1) With this function you can establish diagnostic session with the Instrument cluster via K-Line (KWP1281 or KWP2000)
(2) You can Read/Change odometer value
(3) Read PIN code
(4) Read/Write eeprom
(5) Read ROM/Flash from the Instrument cluster
4) Engine Control Unit
(1) Read EDC17/MED17 flash memory
(2) Read/Write of flash memory (EDC15, EDC16 all types Read/Write Flashmemory via OBDII (K and CAN). Calculation of checksums while programming, ME7.1.1, MED9.x, ME7.5)
(3) Read/Write flash counters (EDC16)
(4) Read/Write eeprom (VAG-EDC15x, VAG-ME7.1.1, VAG-ME7.1, VAG-ME7.5, VAG-Cartronic ME7.8.)
(5) Extracting Security access code / PIN (EDC15, ME7.x, VAG-Cartronic ME7.8, EDC16, EDC17, MED9.x, Simos PPD)
(6) Extracting Component security bytes (EDC15, ME7.x, VAG-Cartronic ME7.8, EDC16, MED17.5.1, MED 9.x, Simos PPD)
(7) Enable/Disable immobilizer (EDC15, ME7.x, EDC16)
(8) Odometer correction (EDC15, EDC16)
5) Kessy adaptation
This function can be used for adaptation of brand new kessy units to the car. This adaptation can be by CAN TP2.0, K-KWP2000 and also can be used with Porsche Cayenne.
6) TV activation ED1/ED2
(1) Using this special function you can change speed limit of MMI compatible vehicles to change speed where TV becomes OFF
7) Key learning
With this function you can learn key/transponder to the vehicle
8) Dump tool
With this function you can calculate security access codes, change odometer and so on from EEPROM dump from the corresponding unit
With this special function you can Read/Write EEPROM memory of the airbag module
Clear the crash data of the airbag module
10) Custom Read/Write
Using this application you can read/program memory in some electronic control unit
11) PIN Convertor
12) Service interval
Using this function you can perform reset of the service reminder, reset of the service interval parameters or change service interval options
13) Remote control adaptation
Using this application, you can learn remote controls
Using this application, you can enable/disable the "Eject" button of the "Navigation" system
15) Cruise control system
Using this application, you can activate/deactivate a cruise control system and change the related
steering wheel electronics( SWE) configuration if SWE unit is available
Update for IMMOPLUS
VVDI immoplus V13.2 upgrade instructions:
1.The way to change the immobilizer data format of color screen dashboard is the same as to change NEC24C32 and NEC24C64, when replace the color screen dashboard, the original immobilizer data will be directly loaded and wrote into the new dashboard.
2.Want to display the original 7byte security code in the position of 12byte security code, move the mouse and edit in the security code edit box.
VVDI immoplus V12.8 Upgrade Instructions:
1.No need to update hardware for run immoplus 12.8
2.Fix the problem that some 5th generation programmer fail to read bcm2 data
3.Fix the problem about failing to adjust A4L/Q5 Meter
4.Fix some bug
1. Your interface must update to newest version then can use this newest version software.
2. Add AUDI/VW 5th generation IMMO generate dealer key and key learning function. Need works with "BDM programmer".Support car model:
3. Support new POLO 4th generation IMMO, dashboard NEC24C32.
4. Fix some bugs.
V10.0 using the instructions
1 to the normal operation of the 8.5 version of the software without having to upgrade the firmware
2 perfect four-generation anti-theft instrument failed login prompt, and customers can tell according to prompts to identify the problem
(3) Add some of the imported models automatic identification
Update NEC +24 the C32 lost them all practices, add color lost them all landing
Pastor color and NEC +95320 smart key learning to add
6. Some bug fixes
New Version: immo plus 8.5
1. Support Visteon dashboard mileage correction(Golf 5 car before 2008 need update hardware)
2. Support all AUDI A3/TT before 2010 mileage correction
3. Fix the bug of some A6L/Q7 after 2009 can not do mileage.
4.support COLOR TFT DASH
How to update?
1. Please download this software: Commander update V1.3
2. Give us the serial number
3. We send you update file by email.
IMMO PLUS 2.0 software and VAG COMMANDER software is allowed to run with a same hardware, but our old VVDI users need to update the hardware firmware before running IMMO plus software with the VAG COMMANDER hardware.
Before update, you have to use COMMANDER UPDATE 1.3 software to read out serial number and send it to your supplier. After your supplier send you the updating data file, please also use COMMANDER UPDATE 1.3 software to open it, then update the hardware, you need only click the button "UPDATE", then a dialog box appears, then you just open the data file.
1pc x VVDI Main Unit
1pc x Chip inductor coil
1pc x USB cable
1pc x OBD 16 CABLE
1pc x CD